PJ Tool – Heavy Duty Right Angle Drill Attachment Reviews

Power Drill Drivers gkulm1775 14 Views 3 Comments

PJ Tool – Heavy Duty Right Angle Drill Attachment

PJ Tool - Heavy Duty Right Angle Drill Attachment

  • Constructed of heavy duty steel with heat treated steel shank
  • Equipped with keyless chuck
  • Can be used with any 3/8″ and larger drill
  • Right angle drill attachment can run forwards or in reverse
  • Measures aprx. 4 1/4″ from the back to the front of the chuck

Our Heavy Duty Right Angle Drill Attachment is great for drilling hard to reach areas.

List Price: $ 28.89

Price: $ 27.50

More Right Angle Drill Products

Reprint Please Indicate: Power Drill Drivers » PJ Tool – Heavy Duty Right Angle Drill Attachment Reviews

Leave a Reply
Cancel Comment
Smilies

Your email address will not be published. Required fields are marked *

  • *
  • *

New comments (3)

  1. 5 of 5 people found the following review helpful
    1.0 out of 5 stars Hope you don't have many holes to drill, November 1, 2016
    By 
    MP -
    Verified Purchase(What's this?)
    This review is from: PJ Tool - Heavy Duty Right Angle Drill Attachment (Misc.)
    I purchased this item as it looked more robust (and was more expensive) than most of the alternatives. I drilled 3 holes using the attachment and it failed while drilling hole number 4. On examination, the 90 degree bend gears are slipping (stripped?). If I had bought this at a local store I would return for sure but harder to do when you get it through Amazon. I cannot recommend this item as the quality is not up to snuff. I really think it should last longer than 3 holes drilled.
    Help other customers find the most helpful reviews 
    Was this review helpful to you? Yes No

    MP2017-09-27 16:50 Reply
  2. 5 of 5 people found the following review helpful
    5.0 out of 5 stars A very good tool, May 28, 2014
    By 
    Verified Purchase(What's this?)
    This review is from: PJ Tool - Heavy Duty Right Angle Drill Attachment (Misc.)
    I purchased this tool as an accessory to a Makita LXT239 driver drill, to perforate wall studs and joists as part of a rewiring project. The goal was to avoid having to buy a dedicated shipwright's drill for the task.

    This tool is very serviceable for the task. It is robust and well made. The housing is solid metal and appears to be powder coated. The keyless chuck works smoothly and firmly.

    There is essentially no play in the shaft, and torque applied to the hex end is transmitted to the chuck easily. It is not difficult to hold the lower housing of the tool and control the position of the drill bit as it enters the stud.

    The shafts turn smoothly and are surprisingly free of friction. In fact, I tested the tool by installing it on the drill, holding the drill point-down at 45 degrees declination, and then ran the drill at maximum speed without touching the tool. The shafts turned so freely that the chuck of the tool remained pointed down, and simply turned in its housing.

    This was a very good purchase and I would not hesitate to buy this too l again.
    Help other customers find the most helpful reviews 
    Was this review helpful to you? Yes No

    Harfindel2017-09-27 17:16 Reply
  3. 1 of 1 people found the following review helpful
    1.0 out of 5 stars :, April 3, 2017
    By 
    Verified Purchase(What's this?)
    This review is from: PJ Tool - Heavy Duty Right Angle Drill Attachment (Misc.)
    Very disappointed with this product. It came in two days, appearance the unit looked well built, that however is not the case. The first one broke midway through the first day of use. P. J. Tools replaced it within two days, great customer service. The second one stripped the gears :/on the fourth hole I drilled. The tool was not being abused in the least, just two small of gears inside. Too bad because it is the perfect size and the keyless chuck was one of the best I have ever used.
    Help other customers find the most helpful reviews 
    Was this review helpful to you? Yes No

    David2017-09-27 17:31 Reply